“Your walls support your home. The weather out there will not be nice and you need to pay special attention to the exterior walls of your house. It isn’t enough to paint your wall to make it waterproof. After dealing with rain, snow, wind, dust and heat of the outside environment, the paint will start peeling off.”
Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.
Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.
Step 1: Properly expose the outside part of the wall
To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.
Step 2: Thoroughly clean the walls
A lot of dust and dirt is carried by air and sticks to the outer part of the wall. To make the process efficient, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned with a broom, brush or scraper. Then use a power washer to wash it off.
Step 3: Check out for the cracks and fill them up
Cracks and holes can develop over time on the exterior walls. Follow up the cleaning process with a thorough look at the cracks and holes on your wall to ensure proper weatherproofing. You can fill them with cement.
Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.
All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.
Inside the cracks, the cement mixture seals them properly. Make sure to remove the loose cement from the wall before you apply the cement.
Step 4: Add a layer of cement waterproofing sealer
If you want to make sure your wall is waterproof, you need to apply the cement waterproofener. After applying the cement in the crevices, let it dry and then apply the waterproof paint sealer. Allow it to become dry after that.
Step 5: Pick the right water-proofer
“There are a lot of products that are waterproof. It’s important to pick the right one for your wall. Pick the water-proofer if it is a concrete wall or a silicate one.”
You can choose between a silicate-based concrete sealer and a concrete waterproofing coating. Pick a plaster waterproof Additive that will strengthen your walls.
Step 6: Apply the water-proofer
Use a roller or brush to apply the water-proofer to the walls. Give a thin coat first, if you want to apply more than one layer. Let the first coating dry before adding the second.
Step 7: Apply tar and heavy-duty membrane
If you want to add more strength to the layers, you need to use a tar-based pitch after drying the cement. It should be applied everywhere on your wall.
After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of the walls.
Step 8: Consider adding gravel
A proper base for the trench is below the footer. The drainage pipes will get adequate support from a 34-inches gravel base. Gravel provides enhanced protection and is long- lasting.
You need to lay the gravel and the drainage pipe-cover. Next to the footer, level the gravel and back-fill it. A covering for the pipe should be at least 3 inches.
Step 9: Add a fabric barrier
Attach the fabric barrier to the pipe. Ensuring a fabric barrier is going to keep dirt out of your system. Simply back-fill the trench and build the top of the dirt relatively high and allow it to settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is
Conclusion:
Your home gets a new life and strength when it is waterproof. Magicrete can help you with good waterproof solutions for your walls. At a very low and affordable price, Magicrete has quality service and proper weatherproofing.
“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”
